neorv32/sw/lib/source/neorv32_spi.c

242 lines
9.9 KiB
C

// #################################################################################################
// # << NEORV32: neorv32_spi.c - Serial Peripheral Interface Controller (SPI) HW Driver >> #
// # ********************************************************************************************* #
// # BSD 3-Clause License #
// # #
// # Copyright (c) 2023, Stephan Nolting. All rights reserved. #
// # #
// # Redistribution and use in source and binary forms, with or without modification, are #
// # permitted provided that the following conditions are met: #
// # #
// # 1. Redistributions of source code must retain the above copyright notice, this list of #
// # conditions and the following disclaimer. #
// # #
// # 2. Redistributions in binary form must reproduce the above copyright notice, this list of #
// # conditions and the following disclaimer in the documentation and/or other materials #
// # provided with the distribution. #
// # #
// # 3. Neither the name of the copyright holder nor the names of its contributors may be used to #
// # endorse or promote products derived from this software without specific prior written #
// # permission. #
// # #
// # THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS #
// # OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF #
// # MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE #
// # COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, #
// # EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE #
// # GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED #
// # AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING #
// # NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED #
// # OF THE POSSIBILITY OF SUCH DAMAGE. #
// # ********************************************************************************************* #
// # The NEORV32 Processor - https://github.com/stnolting/neorv32 (c) Stephan Nolting #
// #################################################################################################
/**********************************************************************//**
* @file neorv32_spi.c
* @brief Serial peripheral interface controller (SPI) HW driver source file.
*
* @note These functions should only be used if the SPI unit was synthesized (IO_SPI_EN = true).
**************************************************************************/
#include "neorv32.h"
#include "neorv32_spi.h"
/**********************************************************************//**
* Check if SPI unit was synthesized.
*
* @return 0 if SPI was not synthesized, 1 if SPI is available.
**************************************************************************/
int neorv32_spi_available(void) {
if (NEORV32_SYSINFO->SOC & (1 << SYSINFO_SOC_IO_SPI)) {
return 1;
}
else {
return 0;
}
}
/**********************************************************************//**
* Enable and configure SPI controller. The SPI control register bits are listed in #NEORV32_SPI_CTRL_enum.
*
* @param[in] prsc Clock prescaler select (0..7). See #NEORV32_CLOCK_PRSC_enum.
* @prama[in] cdiv Clock divider (0..15).
* @param[in] clk_phase Clock phase (0=sample on rising edge, 1=sample on falling edge).
* @param[in] clk_polarity Clock polarity (when idle).
* @param[in] irq_mask Interrupt configuration mask (CTRL's irq_* bits).
**************************************************************************/
void neorv32_spi_setup(int prsc, int cdiv, int clk_phase, int clk_polarity, uint32_t irq_mask) {
NEORV32_SPI->CTRL = 0; // reset
uint32_t tmp = 0;
tmp |= (uint32_t)(1 & 0x01) << SPI_CTRL_EN;
tmp |= (uint32_t)(clk_phase & 0x01) << SPI_CTRL_CPHA;
tmp |= (uint32_t)(clk_polarity & 0x01) << SPI_CTRL_CPOL;
tmp |= (uint32_t)(prsc & 0x07) << SPI_CTRL_PRSC0;
tmp |= (uint32_t)(cdiv & 0x0f) << SPI_CTRL_CDIV0;
tmp |= (uint32_t)(irq_mask & (0x07 << SPI_CTRL_IRQ_RX_AVAIL));
NEORV32_SPI->CTRL = tmp;
}
/**********************************************************************//**
* Enable high-speed mode.
**************************************************************************/
void neorv32_spi_highspeed_enable(void) {
NEORV32_SPI->CTRL |= ((uint32_t)(1 << SPI_CTRL_HIGHSPEED));
}
/**********************************************************************//**
* Disable high-speed mode.
**************************************************************************/
void neorv32_spi_highspeed_disable(void) {
NEORV32_SPI->CTRL &= ~((uint32_t)(1 << SPI_CTRL_HIGHSPEED));
}
/**********************************************************************//**
* Get configured clock speed in Hz.
*
* @return Actual configured SPI clock speed in Hz.
**************************************************************************/
uint32_t neorv32_spi_get_clock_speed(void) {
const uint16_t PRSC_LUT[8] = {2, 4, 8, 64, 128, 1024, 2048, 4096};
uint32_t ctrl = NEORV32_SPI->CTRL;
uint32_t prsc_sel = (ctrl >> SPI_CTRL_PRSC0) & 0x7;
uint32_t clock_div = (ctrl >> SPI_CTRL_CDIV0) & 0xf;
uint32_t tmp;
if (ctrl & (1 << SPI_CTRL_HIGHSPEED)) { // high-speed mode enabled?
tmp = 2 * 1 * (1 + clock_div);
}
else {
tmp = 2 * PRSC_LUT[prsc_sel] * (1 + clock_div);
}
return NEORV32_SYSINFO->CLK / tmp;
}
/**********************************************************************//**
* Disable SPI controller.
**************************************************************************/
void neorv32_spi_disable(void) {
NEORV32_SPI->CTRL &= ~((uint32_t)(1 << SPI_CTRL_EN));
}
/**********************************************************************//**
* Enable SPI controller.
**************************************************************************/
void neorv32_spi_enable(void) {
NEORV32_SPI->CTRL |= ((uint32_t)(1 << SPI_CTRL_EN));
}
/**********************************************************************//**
* Get SPI FIFO depth.
*
* @return FIFO depth (number of entries), zero if no FIFO implemented
**************************************************************************/
int neorv32_spi_get_fifo_depth(void) {
uint32_t tmp = (NEORV32_SPI->CTRL >> SPI_CTRL_FIFO_LSB) & 0x0f;
return (int)(1 << tmp);
}
/**********************************************************************//**
* Activate single SPI chip select signal.
*
* @note The SPI chip select output lines are LOW when activated.
*
* @param cs Chip select line to activate (0..7).
**************************************************************************/
void neorv32_spi_cs_en(int cs) {
uint32_t tmp = NEORV32_SPI->CTRL;
tmp &= ~(0xf << SPI_CTRL_CS_SEL0); // clear old configuration
tmp |= (1 << SPI_CTRL_CS_EN) | ((cs & 7) << SPI_CTRL_CS_SEL0); // set new configuration
NEORV32_SPI->CTRL = tmp;
}
/**********************************************************************//**
* Deactivate currently active SPI chip select signal.
*
* @note The SPI chip select output lines are HIGH when deactivated.
**************************************************************************/
void neorv32_spi_cs_dis(void) {
NEORV32_SPI->CTRL &= ~(1 << SPI_CTRL_CS_EN);
}
/**********************************************************************//**
* Initiate SPI transfer.
*
* @note This function is blocking.
*
* @param tx_data Transmit data (8-bit, LSB-aligned).
* @return Receive data (8-bit, LSB-aligned).
**************************************************************************/
uint8_t neorv32_spi_trans(uint8_t tx_data) {
NEORV32_SPI->DATA = (uint32_t)tx_data; // trigger transfer
while((NEORV32_SPI->CTRL & (1<<SPI_CTRL_BUSY)) != 0); // wait for current transfer to finish
return (uint8_t)NEORV32_SPI->DATA;
}
/**********************************************************************//**
* Initiate SPI TX transfer (non-blocking).
*
* @param tx_data Transmit data (8-bit, LSB-aligned).
**************************************************************************/
void neorv32_spi_put_nonblocking(uint8_t tx_data) {
NEORV32_SPI->DATA = (uint32_t)tx_data; // trigger transfer
}
/**********************************************************************//**
* Get SPI RX data (non-blocking).
*
* @return Receive data (8-bit, LSB-aligned).
**************************************************************************/
uint8_t neorv32_spi_get_nonblocking(void) {
return (uint8_t)NEORV32_SPI->DATA;
}
/**********************************************************************//**
* Check if SPI transceiver is busy.
*
* @return 0 if idle, 1 if busy
**************************************************************************/
int neorv32_spi_busy(void) {
if ((NEORV32_SPI->CTRL & (1<<SPI_CTRL_BUSY)) != 0) {
return 1;
}
else {
return 0;
}
}