neorv32/docs/datasheet/soc_wdt.adoc

104 lines
5.5 KiB
Plaintext

<<<
:sectnums:
==== Watchdog Timer (WDT)
[cols="<3,<3,<4"]
[frame="topbot",grid="none"]
|=======================
| Hardware source file(s): | neorv32_wdt.vhd |
| Software driver file(s): | neorv32_wdt.c |
| | neorv32_wdt.h |
| Top entity port: | none |
| Configuration generics: | `IO_WDT_EN` | implement watchdog when `true`
| CPU interrupts: | fast IRQ channel 0 | watchdog timeout (see <<_processor_interrupts>>)
|=======================
**Theory of Operation**
The watchdog (WDT) provides a last resort for safety-critical applications. The WDT provides a "bark and bite"
concept. The timeout counter first triggers an optional CPU interrupt ("bark") when reaching half of the programmed
interval to inform the application of the imminent timeout. When the full timeout value is reached
a system-wide hardware reset is generated ("bite"). The internal counter has to be reset explicitly by the application
program every now and then to prevent a timeout.
**Configuration**
The watchdog is enabled by setting the control register's `WDT_CTRL_EN` bit. When this bit is cleared, the internal
timeout counter is reset to zero and no interrupt and no system reset can be triggered.
The internal 32-bit timeout counter is clocked at 1/4096th of the processor's main clock (f~WDT~[Hz] = f~main~[Hz] / 4096).
Whenever this counter reaches the programmed timeout value (`WDT_CTRL_TIMEOUT` bits in the control register) a
hardware reset is triggered. In order to inform the application of an imminent timeout, an optional CPU interrupt is
triggered when the timeout counter reaches _half_ of the programmed timeout value.
The watchdog's timeout counter is reset ("feeding the watchdog") by writing the reset **PASSWORD** to the `RESET` register.
The password is hardwired to hexadecimal `0x709D1AB3`.
.Watchdog Interrupt
[NOTE]
A watchdog interrupt occurs when the watchdog is enabled and the internal counter reaches _exactly_ half of the programmed
timeout value. Hence, the interrupt only fires once. However, a triggered WDT interrupt has to be explicitly cleared by
writing zero to the according <<_mip>> CSR bit.
.Watchdog Operation during Debugging
[IMPORTANT]
By default, the watchdog stops operation when the CPU enters debug mode and will resume normal operation after
the CPU has left debug mode again. This will prevent an unintended watchdog timeout during a debug session. However,
the watchdog can also be configured to keep operating even when the CPU is in debug mode by setting the control
register's `WDT_CTRL_DBEN` bit.
.Watchdog Operation during CPU Sleep
[IMPORTANT]
By default, the watchdog stops operating when the CPU enters sleep mode. However, the watchdog can also be configured
to keep operating even when the CPU is in sleep mode by setting the control register's `WDT_CTRL_SEN` bit.
**Configuration Lock**
The watchdog control register can be _locked_ to protect the current configuration from being modified. The lock is
activated by setting the `WDT_CTRL_LOCK` bit. In the locked state any write access to the control register is entirely
ignored (see table below, "writable if locked"). However, read accesses to the control register as well as watchdog resets
are further possible.
The lock bit can only be set if the WDT is already enabled (`WDT_CTRL_EN` is set). Furthermore, the lock bit can
only be cleared again by a system-wide hardware reset.
**Strict Mode**
The _strict operation mode_ provides additional safety functions. If the strict mode is enabled by the `WDT_CTRL_STRICT`
control register bit an **immediate hardware** reset if enforced if
* the `RESET` register is written with an incorrect password or
* the `CTRL` register is written and the `WDT_CTRL_LOCK` bit is set.
**Cause of last Hardware Reset**
The cause of the last system hardware reset can be determined via the `WDT_CTRL_RCAUSE_*` bits:
* `0b00`: Reset caused by external reset signal/pin
* `0b01`: Reset caused by on-chip debugger
* `0b10`: Reset caused by watchdog
**Register Map**
.WDT register map (`struct NEORV32_WDT`)
[cols="<2,<1,<4,^1,^1,^2,<4"]
[options="header",grid="all"]
|=======================
| Address | Name [C] | Bit(s), Name [C] | R/W | Reset value | Writable if locked | Function
.8+<| `0xfffffb00` .8+<| `CTRL` <|`0` `WDT_CTRL_EN` ^| r/w ^| `0` ^| no <| watchdog enable
<|`1` `WDT_CTRL_LOCK` ^| r/w ^| `0` ^| no <| lock configuration when set, clears only on system reset, can only be set if enable bit is set already
<|`2` `WDT_CTRL_DBEN` ^| r/w ^| `0` ^| no <| set to allow WDT to continue operation even when CPU is in debug mode
<|`3` `WDT_CTRL_SEN` ^| r/w ^| `0` ^| no <| set to allow WDT to continue operation even when CPU is in sleep mode
<|`4` `WDT_CTRL_STRICT` ^| r/w ^| `0` ^| no <| set to enable strict mode (force hardware reset if reset password is incorrect or if write access to locked CTRL register)
<|`6:5` `WDT_CTRL_RCAUSE_HI : WDT_CTRL_RCAUSE_LO` ^| r/- ^| `0` ^| - <| cause of last system reset; 0=external reset, 1=ocd-reset, 2=watchdog reset
<|`7` - ^| r/- ^| - ^| - <| _reserved_, reads as zero
<|`31:8` `WDT_CTRL_TIMEOUT_MSB : WDT_CTRL_TIMEOUT_LSB` ^| r/w ^| 0 ^| no <| 24-bit watchdog timeout value
| `0xfffffb04` | `RESET` | | -/w | - | yes | Write PASSWORD to reset WDT timeout counter ("feed the watchdog")
|=======================