217 lines
9.6 KiB
C
217 lines
9.6 KiB
C
// #################################################################################################
|
|
// # << NEORV32: neorv32_xip.c - Execute In Place (XIP) Module HW Driver (Source) >> #
|
|
// # ********************************************************************************************* #
|
|
// # BSD 3-Clause License #
|
|
// # #
|
|
// # Copyright (c) 2024, Stephan Nolting. All rights reserved. #
|
|
// # #
|
|
// # Redistribution and use in source and binary forms, with or without modification, are #
|
|
// # permitted provided that the following conditions are met: #
|
|
// # #
|
|
// # 1. Redistributions of source code must retain the above copyright notice, this list of #
|
|
// # conditions and the following disclaimer. #
|
|
// # #
|
|
// # 2. Redistributions in binary form must reproduce the above copyright notice, this list of #
|
|
// # conditions and the following disclaimer in the documentation and/or other materials #
|
|
// # provided with the distribution. #
|
|
// # #
|
|
// # 3. Neither the name of the copyright holder nor the names of its contributors may be used to #
|
|
// # endorse or promote products derived from this software without specific prior written #
|
|
// # permission. #
|
|
// # #
|
|
// # THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS #
|
|
// # OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF #
|
|
// # MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE #
|
|
// # COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, #
|
|
// # EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE #
|
|
// # GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED #
|
|
// # AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING #
|
|
// # NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED #
|
|
// # OF THE POSSIBILITY OF SUCH DAMAGE. #
|
|
// # ********************************************************************************************* #
|
|
// # The NEORV32 Processor - https://github.com/stnolting/neorv32 (c) Stephan Nolting #
|
|
// #################################################################################################
|
|
|
|
|
|
/**********************************************************************//**
|
|
* @file neorv32_xip.c
|
|
* @brief Execute in place module (XIP) HW driver source file.
|
|
*
|
|
* @note These functions should only be used if the XIP module was synthesized (IO_XIP_EN = true).
|
|
**************************************************************************/
|
|
|
|
#include "neorv32.h"
|
|
#include "neorv32_xip.h"
|
|
|
|
|
|
/**********************************************************************//**
|
|
* Check if XIP module was synthesized.
|
|
*
|
|
* @return 0 if XIP was not synthesized, 1 if XIP is available.
|
|
**************************************************************************/
|
|
int neorv32_xip_available(void) {
|
|
|
|
if (NEORV32_SYSINFO->SOC & (1 << SYSINFO_SOC_XIP)) {
|
|
return 1;
|
|
}
|
|
else {
|
|
return 0;
|
|
}
|
|
}
|
|
|
|
|
|
/**********************************************************************//**
|
|
* Configure XIP module: configure SPI/flash properties.
|
|
*
|
|
* @warning This will reset the XIP module overriding the CTRL register.
|
|
* @note This function will also send 64 dummy clocks via the SPI port (with chip-select disabled).
|
|
*
|
|
* @param[in] prsc SPI clock prescaler select (0..7).
|
|
* @prama[in] cdiv Clock divider (0..15).
|
|
* @param[in] cpol SPI clock polarity (0/1).
|
|
* @param[in] cpha SPI clock phase(0/1).
|
|
* @param[in] rd_cmd SPI flash read byte command.
|
|
**************************************************************************/
|
|
void neorv32_xip_setup(int prsc, int cdiv, int cpol, int cpha, uint8_t rd_cmd) {
|
|
|
|
// reset and disable module
|
|
NEORV32_XIP->CTRL = 0;
|
|
|
|
// clear data registers
|
|
NEORV32_XIP->DATA_LO = 0;
|
|
NEORV32_XIP->DATA_HI = 0; // will not trigger SPI transfer since module is disabled
|
|
|
|
uint32_t ctrl = 0;
|
|
ctrl |= ((uint32_t)(1 )) << XIP_CTRL_EN; // enable module
|
|
ctrl |= ((uint32_t)(cdiv & 0x0f)) << XIP_CTRL_CDIV0;
|
|
ctrl |= ((uint32_t)(prsc & 0x07)) << XIP_CTRL_PRSC0;
|
|
ctrl |= ((uint32_t)(cpol & 0x01)) << XIP_CTRL_CPOL;
|
|
ctrl |= ((uint32_t)(cpha & 0x01)) << XIP_CTRL_CPHA;
|
|
ctrl |= ((uint32_t)(8 )) << XIP_CTRL_SPI_NBYTES_LSB; // set 8 bytes transfer size as default
|
|
ctrl |= ((uint32_t)(rd_cmd & 0xff)) << XIP_CTRL_RD_CMD_LSB;
|
|
|
|
NEORV32_XIP->CTRL = ctrl;
|
|
|
|
// send 64 SPI dummy clocks but without an active CS
|
|
NEORV32_XIP->DATA_LO = 0;
|
|
NEORV32_XIP->DATA_HI = 0; // trigger SPI transfer
|
|
|
|
// wait for transfer to complete
|
|
while (NEORV32_XIP->CTRL & (1 << XIP_CTRL_PHY_BUSY)); // direct SPI mode -> check PHY status
|
|
|
|
NEORV32_XIP->CTRL |= 1 << XIP_CTRL_SPI_CSEN; // finally enable automatic SPI chip-select
|
|
}
|
|
|
|
|
|
/**********************************************************************//**
|
|
* Enable XIP mode (to allow CPU to _transparently_ fetch data & instructions).
|
|
*
|
|
* @param[in] abytes Number of address bytes used to access the SPI flash (1,2,3,4).
|
|
* @return 0 if XIP configuration is OK, -1 if configuration error.
|
|
**************************************************************************/
|
|
int neorv32_xip_start(int abytes) {
|
|
|
|
if ((abytes < 1) || (abytes > 4)) {
|
|
return -1;
|
|
}
|
|
|
|
uint32_t ctrl = NEORV32_XIP->CTRL;
|
|
|
|
// address bytes send to SPI flash
|
|
ctrl &= ~(3 << XIP_CTRL_XIP_ABYTES_LSB); // clear old configuration
|
|
ctrl |= ((uint32_t)(abytes-1)) << XIP_CTRL_XIP_ABYTES_LSB; // set new configuration
|
|
|
|
// total number of bytes to transfer via SPI
|
|
// 'abytes' address bytes + 1 command byte + 4 bytes RX data (one 32-bit word)
|
|
ctrl &= ~(0xF << XIP_CTRL_SPI_NBYTES_LSB); // clear old configuration
|
|
ctrl |= ((uint32_t)(abytes+1+4)) << XIP_CTRL_SPI_NBYTES_LSB; // set new configuration
|
|
|
|
ctrl |= 1 << XIP_CTRL_XIP_EN; // enable XIP mode
|
|
|
|
NEORV32_XIP->CTRL = ctrl;
|
|
|
|
return 0;
|
|
}
|
|
|
|
|
|
/**********************************************************************//**
|
|
* Enable high-speed SPI mode (running at half of the processor clock).
|
|
*
|
|
* @note High-speed SPI mode ignores the programmed clock prescaler configuration.
|
|
**************************************************************************/
|
|
void neorv32_xip_highspeed_enable(void) {
|
|
|
|
NEORV32_XIP->CTRL |= 1 << XIP_CTRL_HIGHSPEED;
|
|
}
|
|
|
|
|
|
/**********************************************************************//**
|
|
* Disable high-speed SPI mode.
|
|
**************************************************************************/
|
|
void neorv32_xip_highspeed_disable(void) {
|
|
|
|
NEORV32_XIP->CTRL &= ~(1 << XIP_CTRL_HIGHSPEED);
|
|
}
|
|
|
|
|
|
/**********************************************************************//**
|
|
* Get configured clock speed in Hz.
|
|
*
|
|
* @return Actual configured XIP clock speed in Hz.
|
|
**************************************************************************/
|
|
uint32_t neorv32_xip_get_clock_speed(void) {
|
|
|
|
const uint16_t PRSC_LUT[8] = {2, 4, 8, 64, 128, 1024, 2048, 4096};
|
|
|
|
uint32_t ctrl = NEORV32_XIP->CTRL;
|
|
uint32_t prsc_sel = (ctrl >> XIP_CTRL_PRSC0) & 0x7;
|
|
uint32_t clock_div = (ctrl >> XIP_CTRL_CDIV0) & 0xf;
|
|
|
|
uint32_t tmp;
|
|
|
|
if (ctrl & (1 << XIP_CTRL_HIGHSPEED)) { // high-speed mode enabled?
|
|
tmp = 2 * 1 * (1 + clock_div);
|
|
}
|
|
else {
|
|
tmp = 2 * PRSC_LUT[prsc_sel] * (1 + clock_div);
|
|
}
|
|
|
|
return NEORV32_SYSINFO->CLK / tmp;
|
|
}
|
|
|
|
|
|
/**********************************************************************//**
|
|
* Direct SPI access to the XIP flash.
|
|
*
|
|
* @warning This function can only be used BEFORE the XIP-mode is activated!
|
|
* @note This function is blocking.
|
|
*
|
|
* @param[in] nbytes Number of bytes to transfer (1..8).
|
|
* @param[in,out] rtx_data Pointer to 64-bit TX/RX data (MSB-aligned for sending, LSB-aligned for receiving (only 32-bit)).
|
|
* @return 0 if valid transfer, 1 if transfer configuration error.
|
|
**************************************************************************/
|
|
void neorv32_xip_spi_trans(int nbytes, uint64_t *rtx_data) {
|
|
|
|
// configure number of bytes to transfer
|
|
uint32_t ctrl = NEORV32_XIP->CTRL;
|
|
ctrl &= ~(0xF << XIP_CTRL_SPI_NBYTES_LSB); // clear old configuration
|
|
ctrl |= nbytes << XIP_CTRL_SPI_NBYTES_LSB; // set new configuration
|
|
NEORV32_XIP->CTRL = ctrl;
|
|
|
|
union {
|
|
uint64_t uint64;
|
|
uint32_t uint32[sizeof(uint64_t)/sizeof(uint32_t)];
|
|
} data;
|
|
|
|
data.uint64 = *rtx_data;
|
|
NEORV32_XIP->DATA_LO = data.uint32[0];
|
|
NEORV32_XIP->DATA_HI = data.uint32[1]; // trigger SPI transfer
|
|
|
|
// wait for transfer to complete
|
|
while (NEORV32_XIP->CTRL & (1 << XIP_CTRL_PHY_BUSY)); // direct SPI mode -> check PHY status
|
|
|
|
data.uint32[0] = NEORV32_XIP->DATA_LO; // RX data is always 32-bit and LSB-aligned
|
|
data.uint32[1] = 0;
|
|
*rtx_data = data.uint64;
|
|
}
|